Official Wiko Kite 4g L4020 Stock Rom Install Link

This guide provides the official procedure for installing the stock firmware on a Wiko Kite 4G (L4020) . Reinstalling the stock ROM is often necessary to resolve software issues like boot loops, "hang on logo" errors, or to restore the device to its original factory state. Pre-Installation Checklist Backup Data : Flashing a stock ROM will erase all user data (contacts, photos, and messages). Ensure you have backed up important files. Battery Level : Charge your device to at least to prevent it from powering off during the process. : Use the original or a high-quality micro-USB cable. Wiko Mobile Required Tools and Drivers You will need to download and install the following on your Windows PC: Wiko Kite 4G : Ensure you download the specific firmware for the Smartphone Flash Tool (SP Flash Tool) : This is the standard utility for flashing Wiko devices. MediaTek (MTK) USB VCOM Drivers : These allow your computer to recognize the phone in "Download" mode. Step-by-Step Installation Guide 1. Install Drivers Install the Wiko USB Drivers and MTK VCOM drivers on your computer. If using Windows 10 or 11, you may need to disable "Driver Signature Enforcement" first to allow the installation. 2. Prepare SP Flash Tool Extract the SP Flash Tool zip folder and right-click on Flash_tool.exe , then select Run as Administrator 3. Load the Firmware In the SP Flash Tool, navigate to the Click on the Scatter-loading Locate the Android_scatter.txt file inside your extracted Wiko Kite 4G stock ROM folder and select it 4. Start the Flashing Process Ensure the dropdown menu in SP Flash Tool is set to Download Only button (green arrow icon). Power off your Wiko Kite 4G completely and remove the battery if it is removable Connect the phone to the computer via USB. If the computer doesn't detect it, try holding the Volume Down button while connecting. 5. Complete the Install Once connected, a red bar will appear, followed by a yellow progress bar as the firmware is written to the device. green ring or "Download OK" message appears, the process is finished. Disconnect your phone, reinsert the battery, and power it on. The first boot may take several minutes. Troubleshooting Tips Device not recognized : Try a different USB port or reinstall the MTK drivers. Fails at start : Ensure you are using the correct scatter file for the L4020 model and that the firmware is fully extracted. : If the phone still loops after flashing, try performing a Hard Reset through Recovery Mode (Volume Up + Power) to clear residual cache. Wiko Kite 4G L4020 firmware file? Wiko Stock ROM Firmware Downloads | PDF - Scribd 16 Dec 2023 —

Official Wiko Kite 4G L4020 Stock ROM Install — Guide Warning: Installing firmware can void warranty and may brick your device if done incorrectly. Back up important data and ensure the phone has ≥50% battery. What you need

A Windows PC (recommended) USB cable Official Wiko Kite 4G L4020 stock ROM (firmware) package for your exact model USB drivers for Wiko (ADB/Fastboot or USB VCom/MTK drivers depending on chipset) Flash tool matching your phone’s chipset (e.g., SP Flash Tool for MediaTek devices) Extracting tool (7-Zip/WinRAR)

Preparatory steps

Verify exact model number: Wiko Kite 4G L4020. Confirm hardware matches the ROM package. Download the official stock ROM for L4020 from a trusted source (Wiko support or verified forum). Do not use ROMs for other models. Download and install required USB drivers on your PC. Reboot after installation. Extract the ROM package and the flash tool to a simple folder (e.g., C:\Wiko).

Install steps (MediaTek/SP Flash Tool example)

Open the extracted ROM folder and locate the scatter file (usually named MTxxxx_scatter.txt). Run SP Flash Tool as Administrator. In SP Flash Tool, click “Scatter-loading” and select the scatter file from the ROM folder. The partitions should populate. Select the proper download mode: official wiko kite 4g l4020 stock rom install

For full clean install: choose “Download” (or “Firmware Upgrade” if recommended by ROM notes). For preserving certain data, follow ROM-specific guidance (not generally recommended).

Click “Download” (or “Firmware Upgrade”). Power off the phone. Remove battery if removable, wait 5–10 seconds, then reinsert (if applicable). Connect the phone to PC via USB while holding the required key if instructed (often Volume Down or Volume Up) — SP Flash Tool usually detects the powered-off device automatically. The tool will begin flashing; do not disconnect. Wait for the green checkmark or success message. Disconnect the phone and power it on. First boot may take several minutes.

After flashing

If bootloop occurs, try wiping cache/data from recovery (Recovery Mode: power + volume key combo). Restore user data from backups. Reinstall updates only from official sources.

Troubleshooting (brief)